Hot Outdoor Recreation Posts
How To: Change the outdrive gear lube on your boat
How to change the outdrive gear fluid on your boat.
How To: Clean a Tippmann 98 Custom paintball gun
This video shows how to clean a Tippmann 98 Custom paintball gun. Materials needed are Pliers, gun lubricant, paper towels, Tippmann 98 Custom and Appropriate sized Allen Wrenches.Step 1. Unscrew barrel, take off hopper connector and tae off bolt cap.Step 2. Next use the Allen wrench to take off Co2 connector and handle grip.Step 3. Then take out the 6 screws that hold the 2 sides of the gun together.Step 4. Take out the front and back bolt.Step 5. Spray lubricant on the places and on both O-...
How To: Pushing off with your rollerblades
In this clip Adam Silverstein with X games physically demonstrates how to push off with rollerblades. First he explains that you need to get comfortable with balancing yourself on the rollerblades, and then you can begin to move forward: while keeping both knees bent, then put one foot straight in front of yourself then and crock the other foot to the side, have it turned so you can push off it, remember to keep both knees bent still, get low then push off on the front and glide. Then switch ...
How To: Control freerun fluidity with an intermediate combo
In this video tutorial, viewers learn how to control fluidity with an intermediate combo. The combo used in this video as a cartwheel to a flash kick. When performing a combo and trying to achieve fluidity, users must have controlled and smooth movements. When you do the cartwheel, land the momentum with one foot over the other. Then as flip back into a flash kick, lift one leg up while the leg on the ground pushes. Users can also perform a back handspring, instead of a flash kick. This video...
How To: Saddle your horse for riding
How to saddle your horse for riding
How To: Maintain the Tippmann A-5 power tube and valve
In this how-to video, you will learn how to maintain a Tippman A-5 Power Tube and Valve. First, pull the valve out of the power tube. Grab the pin with a pair of pliers and give it a firm yank. Next, remove the o-ring and set it aside. Remove the other o-ring off the back. A washer, spring, and plunger will fall out. Remove the other o-ring and valve seat with the tool shown. Now, you can oil the o-rings back up and re-assemble the power tube and valve. Follow the above steps in the reverse o...
How To: Do a cartwheel sideflip freerun trick
In this how-to video, you will learn how to do a cartwheel side flip. First, make sure you can do both a cartwheel and side flip. If you can do these tricks from a standing position, you have more control over the flips. Try to land on the balls of your feet with your legs somewhat apart. Now, come off the balls of your feet and do the side flip. Make sure that you then turn and tuck to perform this correctly. Notice that your arms add momentum as you go through the cartwheel and into the sid...
How To: Choose the correct size for your snowboard
In this video, Sierra Snowboard gives us some tips on how to select the snowboard that's right for you. Each board comes in a number of different sizes, and most boards come with a size chart specific for that board. These charts can be vague, but are good starting points for selecting your size. One thing to consider is your bossy type. The weight of the rider is the primary factor in selecting the size of a snowboard. You'll notice that the height of a rider is not listed on a size chart. I...
How To: Do a "Palm Flip" freerun trick
In this video tutorial, viewers learn how to do a palm flip. Before attempting to do the palm flip, viewers should first perfect and control a back flip. Instead of using the hands to flip on the floor, users will press the hands against the wall to flip. Begin practicing this technique with a mat or some kind of support that will prevent you from landing on the ground. Users should get used to pushing off the wall and landing on the back. This video will benefit those viewers who are interes...
How To: Change your roller skate wheels
This video teaches you how to change the wheels on your roller skates. You will need the replacement set of wheels with the bearings already in them and a skate tool. Remove the wheel by using the skate tool. Remember, righty tighty - lefty loosey. Take off the wheel and pop the new one back on. The key is to put the flat end of the nut on first. Hand tighten the nut and then use the skate tool to tighten it the rest of the way. Tighten it until it stops and then check your wheel. If the whee...
How To: Stop on rollerblades
Learning to skate is one thing, but learning to stop is just as important. In this tutorial Patrick Eaves will walk you through the three different methods of stopping on your inline skates. The first method is the "snow plow". This method is recommended for beginners and only at slow rates of speed. To stop, slowly point your toes towards each other until you come to a rest. The second method is the "heel stops". On the back of one of your skates, usually the right, is a brake pad. When you ...
How To: Do the varial heelflip on a skateboard
In this video tutorial, viewers learn how to do a varial heel-flip on a skateboard. This trick is basically a front-side 180 shove-it with a heel flip. Start with your board backwards so that it will land frontwards at the end of the trick. Put the back foot on the edge of the tail and the front foot with the toes hanging out near the bolts of the board. Pop the board down at an angle and flick the front foot outwards. This video will benefit those viewers who enjoy skateboarding and would li...
How To: Patch a hole in a fiberglass hole
LowkeeLT demonstrates how to patch a hole in a fiberglass boat hull. First, grind around the edge of the hole to make it smooth. Make an angle that goes towards the hull so that the resin won't get caught and create air pockets. Attach kitchen wax paper to the boat as a non-stick material for the poly resin to set against. Then, put down a flexible cutting board by duct taping the two layers on the outside of the hull and pulling it taut. Attach three layers of fiberglass strips with resin to...
How To: Do switch kickflips on a skateboard
In this video tutorial, viewers learn how to do a switch kick-flip on a skateboard. It is the same as a regular kick-flip, except you switch your stance. Users should be able to perform a regular kick-flip before attempting this trick. Start with the front foot near angled near the bolts and back foot on the tail of the board. Pop the tail hard and flick the front foot outwards. Make sure that your weight is centered and do not lean to far back or forward. This video will benefit those viewer...
How To: Replace rollerblade wheels
In this how-to video, you will learn how to replace rollerblade wheels. You will need a skate tool. For each wheel, there is a place to put an Allen wrench. Undo these screws and make sure you do not lose them. Take the screws out, enabling you to also remove the wheel. Do this for each wheel. Remove the space from the wheel. Also, make sure the wheels are well rounded. If it is not, you should rotate the wheel. Push out the bearings with the Allen wrench or another tool. With the new wheel, ...
How To: Do a double leg freerun trick
In this video tutorial, viewers learn how to do a double leg free-run trick. This trick is similar to the side flip, except the side flip needs the legs to be tucked in while the double flip needs the feet to be kept straight. The double leg is at a 90 degree angle in mid-air. Keep your legs together and knees locked. Land on the balls of your feet. Never land on the heels or flat footed. This video will benefit those viewers who are interested in flexibility, aerobics and free-running, and w...
How To: Properly shoot and sight in a compound bow
In this video tutorial, viewers learn how to properly shoot and sight in a compound bow. It is recommended that users use a release. Your body should be perpendicular to the target. Hold the bow vertically, and hold it with a relaxed and secure grip. When you are ready to begin shooting, learn a technique that will help you relax and steady the bow. When you draw the bow string back, you should be looking through the peephole on the bow string and where the target and pins come into view. Thi...
How To: Pump out the waste on your boat for winter
In this Outdoor Recreation video tutorial you will learn how to pump out the waste on your boat for winter. This video is from LIBoatersClub. Take your boat to the waste disposal area and secure it. Remove the cap from the waste tank. Be careful not to drop the cap. Operating the waste disposal unit ashore is very easy. Just switch on the pump, take in some water in to the hose and then attach the hose to the out let on your boat. Hold it tight and open the valve. It will suck out all the was...
How To: Accurately shoot a compound bow
In this video tutorial, viewers learn how to shoot a compound bow. It is deeply recommended that users who use a compound bow should have a release. Put your arrow on the string and push it in until you hear a click. Now hook the release into the D-loop. Your feet should be shoulder width apart and the tips of your feet should be on the target line. Now look at the target and pull back the bow. Your hand should be at the point of your jaw, arrow at the corner of your mouth and string on the t...
How To: Do a switch backside flip on a skateboard
In this video tutorial, viewers learn how to perform a switch backside flip on a skateboard. Before attempting this trick, users should be able to do a switch flip. Begin by going into a switch flip position by covering the bolt with the right foot and cover the tail with the back foot. Ride the board at a moderate speed. As you ride, wind up your shoulder to the backside. Then pop the tail downwards and flick the board with your front foot. Keep your shoulder turning to allow the board to fo...
How To: Polish the guts of a paintball gun with a brillo pad
KRASHARPSHOOTER gives a detailed example on how to better improve performance from the Tippman paintball marker. Some of the advantages to following this method is that it allows the internals to cycle smoothly. He shows us, using a very simple method. The method that he follows in a step by step process in his video is start by taking a Brillo pad and dipping it into water. After that while soap is coming out keep rubbing the pad back and forth on the internal of the paintball marker. He sho...
How To: Disassemble and clean the Tippmann A-5 Flatline barrel
First of all take one eight inch 'Ellen ' wrench and take off the back screw. Now you have to slide out the back plate. There is no need to take the front plate apart. You can clean it using some hot water.You can run hot water over it for a minute. You can also set it in a sink and then run hot water from the tap. You can see a scratch mark on the shaft. That is there to show you the vertical. Now insert in to the round so that this mark is in line with a little mark over it. If it is not al...
How To: Link turns on a snowboard
In this video, we learn how to link turns on a snowboard. First, you are going to want to start in a good balance stance. You will need to learn to use your legs to release your edge and lean into the fall line so you're into a comfortable stance. To release the board into a new turn, drive towards the nose of the board while flattening the foot into the snow. Flex your ankle so you are in a better position to steer the board. You can also rotate your hips to help steer the board. Use your le...
How To: Ollie on a skateboard, for beginners
It takes most everyone a long time to do an ollie but once you have it done it happens all the time. When first starting out it is a good idea to learn the technique in the grass or on some carpet so the board doesn’t roll around. It’s also a good idea to fully learn the ollie in place before you start doing it in motion. Next is foot placement, have your front foot right behind the front bolts on your skateboard and you back foot on the tail. When you press the back foot into the ground lift...
How To: Perform wake jumps
In this video Pro Rider Matt Crowhurst talks about the wake jumps and what needs to be done to execute them. At the beginning of the video Matt says that in order to execute them one has to mater the perfect riding position, being in ease with moving left and right, inside and hillside edge, crossing and execute smooth turns. For executing wake jumps one has to concentrate on three major areas-1. Starting out wide, cruising along and a flat board.2.A progressive edge3.Holding that edge and po...
How To: Rollerblade in 4 steps
In this video, a young boy explains some beginners tips for learning to rollerblade. First start by standing still on the rollerblades. Then try lifting your feet up and down in place, to get a feel for the balance. To move forward, lean forward a little bit and move the skates by pushing them from side to side, back and forth. To jump on rollerblades, skate forward quickly in a straight line and jump with two feet. To twirl on rollerblades, skate forward and point both toes outward, which wi...
How To: Do the frontside and backside 180 on a snowboard
This video illustrates how to do a front side and backside 180 on a snowboard. This process is done by the following steps.Step 1You need a helmet, packing snow, shovel and a snowboard.Step 2Learn to carve a switch.Step 2Make a jump.Step 3Make sure there is no one on the way.Step 4Make sure the hill is long and you go down fast so that you get more air which means that you get more time for a full spin of 180.Step 5Bend your knees down.Step 6Spin your lower body first and focus on landing. th...
How To: Land a fakie frontside flip on a skateboard
In this video tutorial, viewers learn how to do a fakie front-side flip on a skateboard. This trick can be done at any speed. Users should be able to do a front-side flip before attempting this trick. Begin by position the back foot on the tail and front foot below the bolts of the board. Pop the tail down and turn over to your shoulder to rotate your body. Flick the board outwards and then land the 180 degree turn on the board. This video will benefit those viewers who enjoy skateboarding an...
How To: Perform a safety check before horseback riding
In this how-to video, you will learn how to perform a safety check before riding your horse. Do your check on both sides. Go to the off-side first. When you go around, make sure that there is no wear or tear on parts where metal and leather connect. Go back and check different parts of the saddle, stirrups, and cinch. Start off with a bit and make sure it fits. Next, make the cheek pieces are correct and the nose band is correct. You should fit one finger underneath this. The throat latch sho...
How To: Perform a front flip on a wakeboard
In this how-to video, you will learn how to do a front flip using a wake board. The goal is to take it big and take it out to the flats. Do not cut out as far as you can. Take the handle locked in the same position, comfortably towards the chest. This is held in the same position throughout the flip. As for the body position, notice that the rider is in a comfortable knees bent position. Slowly ride off the edge as you approach the wake. This will lessen the pull of the rope at takeoff. This ...
How To: Stop while roller skating backward
In this how-to video, you will learn how to stop while going backwards on roller skates. This will help if you are going too fast and want to stop without falling. Make sure your knees are not locked and you are not going too fast. Take the dominant leg and position it slightly behind you. Next, apply firm but solid pressure on the stopper. Be careful not to place too much, as this will turn you around. Another way involves immediately going back on both stoppers. Your knees must be bent with...
How To: Backflip on rollerblades
In this video tutorial, viewers learn how to perform back-flips on roller-blades. Before attempting this trick, users should be able to do a back-flip off the wall. For beginners, start by learning how to flip. Once you can flip, try flipping off the wall. Depending if you're right or left handed, run to the wall and push off with that foot. When you can wall back-flips, start trying to do them with roller-blades. Go on a ramp and launch off to the side. Once you can flip off the ramp, start ...
How To: Fit a breast collar and back cinch on your horse
First of all you have to check the breast collar which is attached and hanged to the saddle. You have to maintain safety by not ducking under the horse neck. It is better for you to go around and do your job. Keep your head away from the horse head while attaching a collar. Ask your handler to hold the horse for you. Now pick your breast collar up and reach around the horse. Don’t duck under the horse head, but bring the collar belt to your side and then attach it to the ring on the saddle. N...
How To: Stabilize your boat fuel & oil and fog out your engine
Eddie from the Long Island Boaters Club shows in four easy steps how to prepare the engine of your boat for the winter. He discusses the three items needed for proper preparation and makes product suggestions. Then he takes us through the procedure. He starts by pouring an additive to the oil tank and a stabilizer to the fuel tank. Eddie shows us how to attach a hose to the water jacket to flush salt water. He runs the engine for ten minutes. At the end of that period, he demonstrates how to ...
How To: Take apart and oil a paintball marker
This video shows the method to take apart a paintball marker and to oil it. You need a placemat which is optional, paintball marker oil and Q-Tip. Remove the quick-strip pin. Be careful while removing the pin. Hold the striker bolt plug to prevent it from flying off during this procedure. The next step involves taking out the bolt, the striker and the washer which will come along with the rest. Do not oil the delrin bolts under any circumstance. Oil the stock bolt. Always remember to oil the ...
How To: Throw a cast net to catch as much bait as you can
We learn how to throw a cast net. There are many different ways to do this since everyone develops their own personal technique. The way we're shown is this way: First choose your bait. Then get all the rope up in your hand. Lay your hand on the top. Come down about halfway. Lay it back on top again, Hold net up. Grab the lead line. Although many people dislike doing it this way we see him put it in his mouth. Then he grabs the led line and throws it, releasing the lead line at the right moment.
How To: Do a standard kickflip on a skateboard
In this video tutorial, viewers learn how to do a kick-flip on a skateboard. Begin by putting the back foot on the tail and the front foot near the center of the board. Place the feet in an angled or squared position. Ride at a moderate speed. To perform the kick-flip, pop the tail down and flick the front foot outwards. Then catch the board in mid air with the back foot and then with the front foot. Try to land on the bolts of the board. This video will benefit those viewers who enjoy skateb...
How To: Perfect your toeside edging on a wakeboard
In this how-to video, you will learn how to get toe side leverage with this edging drill. This will teach you how to edge properly toe-side. If you are edging out in a bad position, this will cause you to use a bad position with muscle memory. If you edge out properly, you will reinforce a good habit so that you naturally use the position. First, stay outside of the wake. Remove the lead and grab your board shorts so you're forced to edge with your rear hand on the handle. You will have to ed...
How To: Turn on rollerblades
In this how-to video, you will learn how to turn while riding on rollerblades. Start out by going into the ready position with forward momentum. Look into the direction you are going to turn. Keep your body over your skates. Push on the opposite leg of the direction you want to go. This will allow your outside leg to swing around. There is another turn you can try out that is faster but much more unstable. As you are moving, slowly move one skate forward and the other backwards. Pretend you a...
How To: Do a board press on a snowboard
Sierra Snowboard describes how to pull off a board press on your snowboard. The most important aspects of the board press are using your legs to flex the board and setting up your body to balance over the press. Approach the press in an upright, balanced stance and move into the press. Flex down on the leg closest to the end of the board that you want to press and pull up your other leg. At the end of the press, give one last hard press of the leg and pop back into your centered stance. Alter...